Automatic Flight Control Systems Engineering Essay

machinelike fledge lead establishments Engineering EssayWe live in a cosmea where technology is, if not being improved, developed by the second. Everyday new improvements, inventions and discoveries are made. One industry that is always on the lead when it comes to new inventions and innovations is the aura Industry.Over the years, aircrafts have been facing major improvements on the structure, fuel efficiency, life-span, range of flight. But one of the best improvements that have been done on every aircraft (commercial) that had the biggest tint in the Aviation Industry and most probably the main reason why the industry has been booming up is the improvements done in the Avionics section, specifically the Automatic Flight ascertains.In the beginning, Pilots were trained to fly the aircrafts alone. But after several years, it is now the buffer zones programming the computer, telling it where to fly, at what altitude, etc. This computer is the AFCS (Automatic Flight Control S ystem). In todays modern world of flying, it is the AFCS who is technically flying the aircraft, from cruising to set down, and for some until parking. The AFCS has a lot of advantages when compared to human pilots when it comes to flying. Here are some of themThe AFCS has the ability to overcome deficiencies when it comes to perceptual constancy and see to it.The AFCS improved the handling qualities. Such as, when the airspeed or the altitude of the aircraft needs to be constant.The AFCS is to a greater extent accurate and hence is able to carry go forth several tasks that the pilot is not able to do.* Source Emirates Aviation Colleges Automatic Flight Control Systems Book (Chapter 3.1.3)To get a better understanding of the AFCS, the different parts of it pass on be discussed, such as the Autopilot System, Flight Director System, Auto Throttle System and etc.The information about the AFCS will be base on one of Boeings classic aircrafts, the 737-500.FLIGHT MANAGEMENT SYSTEM ( FMS)The Flight Management System is navigation, combined flight control, a Built-In Test Equipment (BITE) and a instruction system. The FMS provides control and operation of five free subsystems to provide lateral navigation (LNAV) and vertical navigation (VNAV) for performance management and optimum flight profiles. The Flight Management System is not labeled to any control panel or any single component as it is an integration of five independent subsystems. These subsystems areDigital Flight Control System (DFCS)Inertial Reference System (IRS)AutothrottleElectronic Flight Instrument System (EFIS)Flight Management electronic computer System (FMCS)* Source United Airlines Boeing 737-322/522 (page 6, Chapter 22-2, Oct 99) from Emirates Aviation College LibraryThis system was designed to increase fuel efficiency, safety and decrease workload. For both(prenominal) pilots, this means that they can destine full FMS operation or Autopilot Flight Director System (AFDS) for a complete automatic flight. They can even use the Control parade Units (CDU) to provide, for manual flight, reference information. Management and operation is totally under the control of the flight crew. There are only if certain operations that can only be implemented by the flight crew. They are landing rollout steering, thrust reversal, speed brake operation, altitude selection, landing gear and flap operation, instrument landing system (ILS) tuning, thrust initiation, brake release, airplane rotation and steering during takeoff roll.* Source United Airlines Boeing 737-322/522 (page 6, Chapter 22-2, Oct 99) from Emirates Aviation College LibraryFMS BUILT-IN TEST EQUIPMENT (BITE)Ground attempt capabilities and self-contained in-flight monitoring are provided for the FMS subsystems. The flight management computer (FMC) coordinates the BITE testing of the five subsystems and must be functional for access to any subsystems built-in test equipment. BITE for the FMS subsystems is accessed f rom both CDUs hardened in the cockpit. Each FMS subsystems run its own systems test. Included in the tests are for its computers, sensor inputs and several interfaces. Any fracture findings during flight are automatically stored for analysis on the ground which is accessed through the bite system.* Source United Airlines Boeing 737-322/522 (page 8, Chapter 22-4, Oct 99) from Emirates Aviation College LibraryTHE BOEING 737-500 CATEGORY*3 commonplace AFCS Category Capability Chart*4Boeing 737-500 AFCS Category Capability ChartThe Boeing 737-500, according to the diagram is in Category 3B. In order for this aircraft to operate at Cat3B weather minimums, the equipment that must be available in Cat2 should be functional. These equipment areBoth Flight DirectorsOne Autopilot in CMDBoth Air info Systems (ADS)Both windshield wipersTwo generatorsBoth EFIS systems displayingRadio AltitudeGlideslope and Localizer DeviationAttitudeAutopilot Status functiond Pitch and Roll ModesDecision tal lnessBoth Radio Altimeter SystemsBoth ILSMarker BeaconBoth IRSNow for the aircraft to operate in Cat3B all the equipment listed for Cat2 must be fully operational, provided that the equipment as follows is includeThe AutothrottleBoth AutopilotsBoth Hydraulic Systems* Source United Airlines Boeing 737-322/522 (page 12, Chapter 22-8, Oct 99) from Emirates Aviation College LibraryAUTOMATIC FLIGHT CONTROL SYSTEM (AFCS)The AFCS or also known as Auto Flight System (AFS) comprises of three independent systems. They areA Yaw dampish SystemA dual Digital Flight Control System (DFCS)An Autothrottle (AT) SystemThese 3 systems provide automatic aircraft stabilization about the roll, pitch and gape axis. The AT and the DFCS systems control the aircraft with the selected Mode Control Panel (MCP) guidance from N1, heading, radio, IRS, FMC and ADC inputs.* Source United Airlines Boeing 737-322/522 (page 10, Chapter 22-6, Oct 99) from Emirates Aviation College LibraryYAW-DAMPER SYSTEMThe Yaw Dampe r System is composed of various components, such asYaw Damper Engage switchWarning AnnunciatorYaw Damper CouplerIntegrated Flight System Accessory Unit (IFSAU)Yaw Damper Engage solenoidPosition Transducer and slay Valve on the rudder Power Control Unit (PCU)Yaw Damper position Indicator* Source United Airlines Boeing 737-322/522 (page 12, Chapter 22-8, Oct 99) from Emirates Aviation College LibraryThe Yaw Damper System smoothens the flow of air that causes the aircraft to yaw and thus causes it to Dutch Roll. The Dutch Roll is a phenomenon that occurs when a typefacewind hits the aircraft which causes it to yaw. This yawing motion exposes one side of the wing to the wind more than the other side. The exposed side of the wing, gains more speed and more speed generates more lift on that particular side. The lift that was generated on the exposed side of the wing causes the aircraft to roll. Hence, the term Dutch Roll.The Yaw Damper System is a stability augmentation system that work s full time, providing yaw axis damping for the complete flight, including both takeoff and landing. It is connected in series so that none of the rudder feedback is applied to the pedals. This now allows the Yaw Damper System to operate in an independent expressive style without interfering the initiated rudder commands by the flight crew. Both the yaw rate and the yaw direction are detected using a rate sensor located in a Yaw Damper Coupler. The rate sensor of the Yaw Damper is sensitive that the rudder is displaced at a proper time to dampen out any sidewinds hitting the aircraft before it can obviously affect the flight path of the aircraft.* Source United Airlines Boeing 737-322/522 (page 12, Chapter 22-8, Oct 99) from Emirates Aviation College LibraryThe Yaw Damper potence is only 3 deflection of the rudder. Its actuator gets no turning commands from the longitudinal axis AP. The Boeing 737-500 does not have a 3-axis AP. It only has 2 which is the pitch and roll axes only. I n this aircraft, turn coordination is not available. A roll command which sends a cross feed sign on in proportion to the bank angle due to aircraft banking, is move to the Yaw Damper to prevent undesirable opposition to roll attitude.* Source United Airlines Boeing 737-322/522 (page 12, Chapter 22-8, Oct 99) from Emirates Aviation College Library*5Yaw Damper System diagramYaw Damper OperationThe Yaw Damper is confined to 3 modes of operation. These modes are synchronization mode, engaged mode interlocks and logical system and engaged mode operation. forward the yaw axis engagement, the Yaw Damper coupler is in the synchronization mode for 2 seconds. The synchronization mode provides a null output signal to the electro-hydraulic pitch valve to prevent a sudden change in the Yaw Damper coupler. The mode is accomplished by returning the controlled signal back to the output amplifier. The output of the valve amplifier is reduced to null as the output of the integrator increases, causing the signal to be cancelled. Prior to the engagement of the Yaw Damper its actuator remains at the middle(a) which nulls the position feedback to the Yaw Dampers coupler.* Source United Airlines Boeing 737-322/522 (page 14, Chapter 22-10, Oct 99) from Emirates Aviation College LibraryThe system is activated by placing the Yaw Damper switch on the flight control module to ON. Both Bs of the flight control switch and system hydraulic occasion must be ON and available, respectively, in order to power the Yaw Damper actuator portion of the PCU. 2 seconds after the Yaw Damper is on, the YAW DAMPER light extinguishes. The Integrated Flight Systems Accessory Unit (IFSAU) contains the logic to engage the system, monitor the engagement and illuminate the amber-colored Yaw Damper disengaged annunciator light. If, for over 2 seconds, the AC power is lost, the YAW DAMPER light illuminates and the Yaw Damper switch returns to OFF position. The Yaw rate gyroscope which is located inside the Yaw Damper coupler senses the movements by the yaw axis. The coupler only responds to yaw movements that produce the Dutch Roll. Before the command signals are applied to the transfer valve which is located inside the Yaw Damper actuator, it is first filtered and amplified. The transfer valve then sends hydraulic pressure in order to deflect the rudder and reduce the aircrafts oscillation by the yaw axis. The output of the Yaw Damper actuator is summed with the rudder pedal manual input in order to move the main rudder Power Control Unit (PCU) that controls the rudder. Now as the actuator moves the linear variable displacement tranducer (LVDT) supplies the signal of the position feedback to nullify the signal coming from the yaw rate gyroscope. When the movement (by the yaw axis) stops, the feedback signal returns the rudder to the original position.